鑫港机械-专注各种型号整套造纸机、高速卫生纸造纸机、造纸配件、制浆设备、纸加工设备等,可提供设备出口贸易服务!

联系我们

沁阳市鑫港造纸机械厂

  • 手机(微信同号)
  • 13839172345
  • 13526609856
  • 电话:
  • 0391-5662345
  • 0391-5661666
  • 邮箱:395457270@QQ.com
  • 地址:河南省沁阳市王曲乡里村工业园

整套造纸机

您当前的位置:首页 > 产品中心 > 整套造纸机 >

2100快速卫生纸机配置及说明

产品分类:整套造纸机

主要用于生产抄造13-30g/㎡卫生原纸或纸巾原纸,经深加工后制成卫生纸、餐巾纸、面巾纸、手帕纸等高级卫生纸用品。...

咨询热线:13839172345

产品详情

沁阳市鑫港造纸机械厂

沁阳市鑫港造纸机械厂

XG2100快速卫生纸机配置及说明

 Disposal and instruction of QJD2100-G1W1K
high speed tissue paper making machine
 
一、  用途  Use
主要用于生产抄造13-30g/㎡卫生原纸或纸巾原纸,经深加工后制成卫生纸、餐巾纸、面巾纸、手帕纸等高级卫生纸用品。
Paper weight : 13-30gms,
Raw material : waste tissue paper, newspaper, printing paper
Finish paper: jumbo rolling tissue paper
二、工艺参数 
1、浆料:适用于浆板、废纸等各种原料
2、上浆浓度:0.3-0.9℅
3、叩解度:30°-38°SR
4、纸页干度:
出网笼干度:18-20℅
进烘缸干度:36-40℅
出烘缸干度:90-94℅
成纸干度:90-94℅
5、横向收缩率:8-10 ℅
6、运转效率:22h/d
7、抄造率:94℅
8、成品率:95℅
9、托辊线压:60 KN/m
鑫港机械-专注卫生纸造纸机械
Crafts parameters:
Pulp : wood pulp plate, waste paper etc as raw material
Feeding pulp concentration : 0.3-0.9‰
Beating degrees : 30-38°SR
Paper sheet dryness 
   come out from wire case : 18-20%
Before go through MG cylinder : 36-40%
      Come out from MG cylinder : 90-94%
   Finish tissue : 90-94%
 Lateral shrinkage : 8-10%
 Day running hours: 22 hours
 Papermaking rate : 94%
 Yield : 95%
 Touch roll line pressure: 60 KN/m
三、配套参数:          
1.交流电压:380V;50Hz   
2.控制电压:220/24V       
3.清水压力:0.3Mpa;工作压力:0.2Mpa
4.压缩空气压力:0.8Mpa;工作压力:0.5Mpa
5.水蒸汽压力:0.6Mpa;工作压力:0.3Mpa
6.吸水箱真空度:20-40Kpa
7.水质要求:纯净无色、无杂质、PH值6.8
Supporting parameter
AC voltage : 380V;50Hz
Control voltage : 220/24V
Water pressure : 0.3Mpa; working pressure: 0.2Mpa
Compressed air pressure : 0.8Mpa; working pressure : 0.5Mpa
Steam pressure : 0.6Mpa ; working pressure:0.3Mpa
Vacuum suction tank : 20-40Kpa
Water requirement : pure color, remove impurities, PH value 6.8
四、技术参数: 
1、抄造定量:13-30g/㎡
2. 净纸宽度:2100mm      
3. 设计车速:200m/min   
4. 工作车速:130-180m/min
5. 公称产量:5-7T/D     
6. 纸机轨距:3000mm      
7. 起皱速率:15-30℅     
8. 传动方式:Y型交流电机、分部传动
9. 控制方式:变频器调速  
10.装机容量:
网笼:7.5Kw;烘缸:45Kw;卷纸机:5.5Kw合计:58Kw
11.排列方式:单层布置、分左/右手机
Main technical parameters:
Papermaking quantitative: 13-30g/㎡ high wrinkles toilet paper
Net width of paper :2400mm
Designed speed : 200m/min
Working speed: 160-180m/min
Nominal capacity : 5-7T/D
Base plate distance : 3000mm
Wrinkling rate : 15-30℅
Transmission : Y-type  AC motor drive partly, frequency contro
Control way:frequency control
Capacity:cylinder mould7.5Kw;MG cylinder motor :45kw
Roll-cylinder motor: 5.5kw  Total:58Kw
Arrangement : single-layer , the left and right hand arrangement
五、设备说明:  
1.园网、洗涤部          
1.1园网槽采用中弧形压力式高位上浆。槽体用碳钢板焊作,接触浆料部分内衬不锈钢,内表面打磨光滑不挂浆;弧形板用不锈钢焊制;采用方椎总管进口多管布浆三级阶扩匀浆装置,使浆料与分散剂混合后经过多级不断扩散、收缩。
1.2网笼:¢1800×2550×3000mm,1只,配用113624轴承及壳,轮辐为灰口铸铁,间距135mm,外轮辐采用不锈钢压片,表面采用不锈钢绕片,厚度1.5mm,间距8mm,校动平衡.不平衡量不大于自重的1‰。
1.3配套网笼传动,含电机、减速机、联轴器及传动地轨。
1.4伏辊:¢500×2550×3000mm,1条,配用315轴承及壳,辊体采用Q235钢板卷制,轴料采用45#钢.铸铁闷头红装,校动平衡,不平衡量不大于自重的1‰,橡胶硬度:绍尔“A”36-40°厚25mm。
1.5真空吸水箱:4件,箱体为钢板焊制,面板为高分子聚乙烯,厚度20mm。
1.6洗涤装置:2寸喷水管2根,喷头为不锈钢扇形,间距80mm,工作宽度2600mm,移动喷水管1根,清洗网笼用。
1.7洗网槽:1套,钢板折边,两边含水封装置。
1.8机架:采用型钢及钢板焊制。
Equipment  introduction
1.1 Wire parts, washing parts
Cylinder tank uses curved slot-type high pressure sizing. Tank is carbon steel plate welded, lining is stainless steel and inner surface is polished smooth without sizing. Arc plate is stainless steel welded. Three stage expansion devices make the pulp mixed with dispersing agents spread and shrink.
1.2  Wire case : ¢1800×2550×3000mm,1 set,bearings 113624,
bearing bracket,the wheel is gray cast iron,span:135mm, outside of wheel is made of stainless steel presser, surface is stainless steel winding, thickness 1.5mm, span:8mm,Balance of correction:≤1‰ of dead weight.
1.3 Supporting cylinder mould Drive (motor, decelerator, coupling, driving gauge.)
1.4  V roll: 1¢500×2550×3000mm, bearings315, bearing bracket, Q235 Steel board for roll body, 45# steel for Axis. cast iron, Balance of correction:≤1‰ of dead weight. rubber hardness: A”36-40°.thickness:25mm.
1.5  Vacuum tank            4sets
Welded steel for tank body, PVC panel thickness 20mm
1.6  Washing device :2-inch water pipe 2 paces, nozzle is stainless steel
fan-shape, 80mm intervals, covering width 2600mm, mobile water pipe 1pcs to wash cylinder mould.
1.7 Wire slot: 1 set, the edge for steel board, two sides contain water seal device.
1.8 Rack: section and steel board
2.烘缸部 Dryer can part
2.1烘缸:¢2500×2550×3000mm,1只,采用铸铁添加合金制成,硬度:HB210-230°,工作压力0.3Mpa,含3113156轴承及座,含压力检验合格证。
Dryer can: ¢2500×2550×3000mm,1set, Made from cast iron and alloy, hardness HB210-230°,working pressure 0.3Mpa, bearings 3113156, bearing bracket, with inspection certificate by authorities of pressure.
2.2配套烘缸进气头和虹吸管。Steam gas and siphon
2.3托辊:¢600×2550×3000mm,1条,铸铁辊芯,包胶厚度20mm,硬度:绍尔“A”91-95°厚20mm,线压600N/㎝,配用113632轴承及轴承壳,校动平衡,不平衡量不大于自重的1‰,车制沟纹。
Touch roll: ¢600×2550×3000mm,1set, Cast iron roll core, rubber thickness 20mm, line pressure 600N/cm, with bearings 113632 and bearing room, Balance of correction:≤1‰ of dead weight, Car system grooves
2.3托辊采用气动装置,气胎型号¢480×3。
Touch roll use pneumatic device ,style of tire ¢480×3.
2.4气罩:采用呼吸式气罩,配套鼓风机、散热器、风管及引风机。
Steam cover: breathing steam cover, auxiliary fans, radiator air hose fan.
2.5刮刀:2把,卫生纸机专用气动刮刀,2把刮刀均能正常出纸,刮刀体为自由式气动加压,加压汽缸带缓冲装置,汽缸型号¢100×150,定槽式刀片固定形式,刮刀高度为可调式,带纸屑斗.
Doctor blade:              2 sets
Pneumatic wrinkling scraper of toilet paper: 2sets it can wrinkle the paper uniformly, Doctor blade is Pneumatic press freely, pressure cylinder with buffer,  cylinder style ¢100×150, Doctor blade is stable, the height  is changeble with paper box.
2.6配套烘缸传动,含电机、减速机、联轴器,大小齿轮及传动地轨。
Supporting dryer can,
drive(motor, decelerator, coupling, big gear wheel and small gear wheel, driving gauge.)
2.7导辊:¢219×2600×3000mm,9条,配用311/312双排轴承,包胶厚度10mm,无缝钢管红装闷头,轴料用45#钢,含轴承壳及瓦架, 校动平衡,不平衡量不大于自重的1‰。
Guide roll : ¢219×2600×3000mm,9set,with 311/312 double bearing, glue thickness 10mm 45# steel for Axis. Bearing bracket and tile rack. Balance of correction:≤1‰ of dead weight.
2.8舒展辊:¢219×2600×3000mm,1条,配用311/312双排轴承,包胶厚度15mm,车制双面螺旋,无缝钢管红装闷头,轴料用45#钢,含轴承壳及瓦架, 校动平衡,不平衡量不大于自重的1‰。
Stretch roll: ¢219×3000×3300mm,1set,with 312/313 double bearing, glue thickness 15mm, Car system double spiral , 45# steel for Axis. Bearing bracket and tile rack. Balance of correction:≤1‰ of dead weight.
2.9电动张紧器:1套     Eclectic Tensionless :1 set
2.10气动校正器:1套,含传动侧高瓦架及自动纠偏装置。
Pneumatic Correction:1 set, with drive tile rack and  automatic correction device.
2.11导辊瓦架:16件。   Guide roll tile rack :16 sets
2.12机架:采用型钢及钢板焊制。
Rack: make from section and steel board
3、卷纸部  Rolling paper part
3.1¢800园筒卷纸机:1台。
¢800 Horizontal winding machine:1 set
3.2冷缸¢800×2400×3000mm,1只,配用滚动轴承及轴承座,校动平衡,不平衡量不大于自重的1‰。
¢800×2400×3000mm Cold cylinder :1 set, with bearings and bearing bracket, Balance of correction:≤1‰ of dead weight.
3.3卷纸辊:3条。  Paper roll:3 sets
3.4气动控制柜,1台。Pneumatic control cabinet:1 set
3.5配套传动,含电机、减速机、联轴器,大小齿轮及传动地轨。
Transmission :( motor, decelerater, coupling, big gear wheel and small gear wheel, driving gauge.)
3.6机架:采用铸件及钢板制做。
Rack: make from castings and steel board.
4、基础部     Basic part
4.1铸铁地轨1套,退火处理后精加工,分单、双槽两种规格
Cast iron gauge:1 set. After annealing treatment, finishing, Contain: single, double slot
4.2地脚螺栓1套,含螺母及垫圈。
Anchor bolts:1 set,(nuts, gasket)
4.3校正地轨用斜鉄1套。Correction gauge :1 set.

上一篇:牛皮纸瓦楞纸造纸机

下一篇:高速卫生纸机|卫生纸造纸

标签:高速卫生纸造纸(1)

【本文标题】2100快速卫生纸机配置及说明,【本文网址】http://www.chnzzjx.com/ztzzj/123.html

推荐产品

2880型喷浆式高速卫
2880型喷浆式高速卫
1880型卫生纸造纸机
1880型卫生纸造纸机
2880型高速卫生纸机
2880型高速卫生纸机
3200型卫生纸造纸机
3200型卫生纸造纸机
Copyright © 沁阳市鑫港造纸机械厂 版权所有技术支持:伟置电子豫ICP备16011558号